XJEase compiler warnings

• Warning 001: Cannot set net 'net' to be constant val - net is classified as a ground net
• Warning 003: Cannot set net 'net' to be constant val - net is classified as a power net
• Warning 006: Cannot drive net 'net' to constant value: net cannot be driven from any JTAG devices
• Warning 007: Multiple constant values specified for net net - will choose value
• Warning 009: Pin pin is set to multiple constant values - it will be set to value
• Warning 010: Pin pin on bus bus does not exist on device
• Warning 011: Common control being set to conflicting values. Control cell applies to:
• Warning 012: Net net has pins with conflicting internal pull values. Pin pin1 has value value1 whilst pin pin2 has value value2. Internal pulls will not be tested on this net.
• Warning 013: Coupling connector couples net to power or ground : consider categorising the coupling as an Ignore device
• Warning 014: Bias termination connector is not attached to a termination voltage net
• Warning 015: Net net1 is terminated to termination reference net net2 but also grouped differentially (via pin pin1) with net net3, which is not terminated to net2
• Warning 016: Net net1 is terminated more than once - the net is terminated to termination reference net(s): nets
• Warning 022: Conflict found on net net: pin pin of device and pin pin of device are both output-only pins
• Warning 025: Cannot write to pin pin number (bit bit number of bus bus name) on device: reason
• Warning 026: Cannot read pin pin number (bit bit number of bus bus name) on device: reason
• Warning 028: Cannot read the pin name pin; it is not defined in the pin mapping
• Warning 030: Connecting two pins on ignored device device: use a PDD file instead
• Warning 031: Unable to connect device.pin and device.pin: reason
• Warning 032: TMS pin pin is not connected to the same net as TMS pin pin
• Warning 033: TCK pin pin is not connected to the same net as TCK pin pin
• Warning 034: There was a mismatch in the pins on device and device while connecting them together
• Warning 036: Pull Resistor device joins 2 Power nets: net1, net2
• Warning 037: Pull Resistor device joins 2 Ground nets: net1, net2
• Warning 038: Pull Resistor device joins Power net: net1 to Ground net net2
• Warning 039: Pin pin has a compliance value of hilow, but is not shorted or pulled to pwrgnd
• Warning 040: xjlinktype connection: type pin pin is not connected to the type pin on the XJLink (xjlinkpin)
• Warning 041: xjlink-connector connections: No connection is defined from a ground pin on xjlink-connector to a ground net on the board. Lack of a ground connection could cause unexpected circuit behaviour.
• Warning 042: JTAG device device is not part of any JTAG chain
• Warning 049: message
• Warning 050: message
• Warning 051: Possible overflow in assignment
• Warning 052: Differing widths in SET assignment
• Warning 053: Globals in device files are not supported
• Warning 054: Format string was invalid: message
• Warning 055: The SVF_RESET and STAPL_RESET flags are ignored when inside a test reset sequence
• Warning 056: CONST is not valid on a function declaration and will be ignored
• Warning 057: Invalid pin name name on component device (bsdlfile)
• Warning 058: Integer variable declared with zero width
• Warning 061: Assignment expression uses a non-constant variable, nonConstName
• Warning 070: Pin(s) problemPin in gate with pins otherPins on Logic Device deviceRef not found in the netlist - logic gate has not been created
• Warning 071: Logic gate on device (pins listOfPins) specified in file has none of its pins present in the netlist
• Warning 072: Could not satisfy all constant pins and disable values on logic block block. This may be due to conflicting requirements, lack of access or lack of a suitable state in the truth table. Running Connection Test may give more information.
• Warning 080: warning
• Warning 081: The BSDL file does not specify a default footprint to use and no footprint has been specified: defaulting to the first footprint in the BSDL file: footprint
• Warning 082: The default footprint specified in the BSDL file was not found: using footprint instead
• Warning 083: The BSDL file for component device contained count extra pins not referenced in the netlist. This may indicate a problem with the BSDL file. Please refer to "BSDL Files" in the "Project Setup" section of the troubleshooting guide for more details.
• Warning 085: warning
• Warning 086: device contains both numeric and alphanumeric pin names: the device will be treated as a value device, and pins of any other type will be ignored
• Warning 090: tap signal [on chain 'chain'] pulled to power by resistor with value of value. Recommended value is between minvalue and maxvalue.
• Warning 091: tap signal [on chain 'chain'] pulled to power/ground by resistor with value of value. Recommended value is between minvalue and maxvalue.
• Warning 092: TDO signal [on chain 'chain'] has series resistor resistor with value of value to TDO pin of device device. Recommended value is between minvalue and maxvalue.
• Warning 094: TCK signal on net net has resistor resistor with value of value. Recommended value is a 68ohm resistor in series with a capacitor to ground.
• Warning 095: TCK signal on net net has capacitor capacitor to ground with value of value. Recommended value is 100pf.
• Warning 097: Unable to determine the value of pull resistor resistor on tap [on chain 'chain']. Check it is between the recommended values of minvalue and maxvalue.
• Warning 098: Unable to determine the value of pull resistor resistor on tap [on chain 'chain']. Check it is between the recommended values of minvalue and maxvalue.
• Warning 099: Unable to determine the value of TDO series resistor resistor [on chain 'chain']. Check it is between the recommended values of minvalue and maxvalue.
• Warning 100: The TCK frequency specified is greater than the recommended frequency of at least one component
• Warning 101: Error ignored while setting TCK frequency in the test reset sequence
• Warning 102: Test point not parsed - invalid value in columnName column
• Warning 103: Net net defined as ictCategorisation in powerSupplyFile has been categorised as existingCategorisation
• Warning 104: device is marked as ictCategorisation in filename but is categorised as projectCategorisation in the project
• Warning 105: All voltage domains in filename are the same. Please check that this is the correct voltage domain for all test points accessed through the external hardware.
• Warning 107: filename contains description test points which are not supported. hint
• Warning 108: filename contains multiple definitions of the test point priority of pad shape description
• Warning 109: Unable to drive default value of value for pinName on net netName
• Warning 110: Unable to set pinName on net netName as Input as drivers cannot be disabled
• Warning 111: Unable to drive default value of value for pinName on net netName. This value has still been added to the safe bitstream and will be applied if possible following active profile or subchain changes.
• Warning 112: Unable to set pinName on net netName as Input as drivers cannot be disabled. This value has still been added to the safe bitstream and will be applied if possible following active profile or subchain changes.
• Warning 130: There are no devices tagged for the circuit function test functionName. The Test Coverage Summary report will not report any coverage from this test.
• Warning 131: The tagged device deviceName for test function functionName could not be resolved. No test coverage will be reported for the device from this test.
• Warning 140: device is categorised as Test but does not appear in test list
• Warning 160: The value "value" specified for tag tagName is invalid. reason
• Warning 161: The tag tagName is not a recognised XJEaseDoc tag.
• Warning 162: The tag tagName cannot be used in this context. reason
• Warning 163: The tag tagName requires at least number argument(s).
• Warning 164: The tag tagName requires at most number argument(s).
• Warning 165: In this context the tag tagName must be specified at least number time(s).
• Warning 166: In this context the tag tagName may only be specified at most number time(s).
• Warning 200: tdiPin indirectly driven by profile profile
• Warning 201: External hardware 'externalHardwareName' is selected in profile 'profileName' but is currently disabled.
• Warning 999: Too many warnings to display. Clear some warnings to see more.